Электростатические фильтры GEA (сухие и мокрые)

Dry ESP

The GEA dry Electrostatic Precipitator (ESP) is a highly effective, energy-and-cost-saving alternative to bag filters. Compared to a conventional bag filter, an ESP needs between 2 and 3 times less vertical space to clean a similar volume of gas.

An essential factor in achieving maximum collection efficiency is an even distribution of the gases over the entire cross-section of the precipitator. This is achieved through the optimized design of the precipitator’s inlet transition and the installation of specially designed gas deflection and distribution plates.

Depending on the required gas volume flow and dust content reduction, the system is customized to suit the customer´s needs from a number of available options. Thanks to the employed materials, the ESP can withstand temperatures of up to 450 °C. The high temperature level allows an easy heat recovery downstream the ESP.

Working principle

Casing of frame-type design are a proven, reliable, and economical solution for horizontal precipitators.

In this type of Electrostatic Precipitator, the collecting electrodes are parallel vertical plates. They form passages, in the center of which, the discharge electrodes are suspended from insulators. The plates are shaped as to provide quiescent zones to prevent the collected dust from being stirred up and re-entrained by the gas stream.

The discharge and collecting electrodes are supported by box-type roof beams. The loads are transmitted via stanchions from the roof beam ends to the precipitator support structure. The roof covering and side walls are specifically designed to withstand the internal precipitator pressure and the wind forces.

The precipitators are equipped with rigid discharge frames made of welded tubes into which the discharge electrodes are securely fixed. This design eliminates electrode oscillations resulting from the electrical field and the gas flow. Firm fastening of the electrodes to the frame, e.g. by bolting and welding, prevents spark erosion at the fixing points.

The discharge frames of each precipitation field are suspended from four support insulators mounted on the roof structure of the precipitator casing.

Each insulator is equipped with electric heating to ensure that the temperature at the insulator will not be below the dew point when the plant is started up cold. If necessary, a small flushing air stream is used to keep the insulator interior clean.

Main Benefits

• High degree of separation, even with fine dusts
• Even flow distribution achieved through specially designed gas distribution plates tested with CFD modeling
• Electrode rapping with reliable and robust tumbling hammer systems, superior to magnetic/top rapping
• Reliable insulator design for long-term operation
• High voltage supply with T/R-sets and controllers
• Comprehensive experience in ESP design
• Low operating costs due to low pressure loss and maintenance requirements
• Long service life and high availability
• Can be retrofitted effectively in existing systems 
• Modular design with high pre-assembly degree
• Easy access for maintenance and servicing 

Wet ESP

Wet Electrostatic Precipitators (WESP) are used in many processes in which dry separation is not possible due to the characteristics of the dust or gas. They are ideal for separating the finest dust-laden water droplets, aerosols and tar as well as oil-containing exhaust gases. 

WESPs provide high operational safety, long service life and efficient separation of sub-micron particulate, aerosols and fumes from industrial gas streams. These can include heavy metals such as lead, arsenic or cadmium, condensed acid aerosols like sulfur trioxide (SO₃) or condensed volatile organic compounds (VOC’s). The use of electrostatic forces minimizes energy costs when compared to other technologies which require large amounts of energy to overcome resistance to air low

The GEA WESP is a proprietary, robust design with a unique alignment mechanism to hold electrodes rigidly in place. This reduces installation and maintenance times and improves performance. The field strength is consistently maintained at high levels with minimal sparking, resulting in the highest available efficiency. The greater the electrostatic fields strength, the greater the particle migration speed (speed component towards the collection tube). Increasing migration speed brings a higher particle collection efficiency with lower specific collection area (SCA) than conventional precipitators. Lower SCA means a smaller, less expensive unit.

Wet ESP

The principle and design of the wet-type precipitator is essentially identical to the dry type, the difference between them being the rapping systems.

As their use is limited to the cleaning of humid, saturated gases, mechanical rapping systems are not required for cleaning the discharge and collecting systems. The effect of the electric field causes a film of liquid to form on the collecting electrodes that continually drains off. In this way, any dust particles present are carried away in suspension. The precipitators are cleaned at set intervals by spray nozzles.

Tubular Wet ESP

Tubular precipitators consist of parallel vertical tubes with a circular or hexagonal cross section with the discharge electrodes suspended from insulators at their center. The tubes are earthed and form the collecting electrodes.

The discharge electrodes may be made of ordinary round wire stretched taut by weights. Other designs are starshaped and barbed electrodes made of lead with a supporting steel core. They are suspended from a top guide frame and anchored to the center of the tube. The bottom guide frame ensures that they are correctly spaced in the tube mid-sections at the bottom. The gas flow is, generally, in vertical direction.

Working principle

GEA’s wet electrostatic precipitator (WESP) uses electrostatic force to remove particulate. 

Turing canes and a perforated plate evenly distribute the gas flow inside of the wet electrostatic precipitator and achieve an even gas distribution. The collecting electrode strips are freely suspended from the top of the plate support. Each row of strips is firmly fixed at the bottom to a set of rapping bars. The electrodes and rapping bars are free to expand downwards under the influence of heat.

The discharge system must be periodically cleaned from adhering dust. This is performed by hammers striking anvils which are firmly fixed to the discharge frames. The hammers are actuated by a cam release device situated outside the gas stream.

Each electric field is equipped with a Rotohit^® rapping device with the hammers for the individual rows of collecting electrodes. These hammers are mounted on the hammer shafts in a staggered pattern, thus striking the anvils of the plate rapping bars in succession. This means that the respective collecting electrode rows are vibrated and cleaned consecutively and periodically.

Main Benefits / Features / Advantages

• High degree of particle separation — more than 99.9%.
• Minimal pressure loss
• Low energy consumption
• Excellent availability & reliability
• Quick installation
• Minimal maintenance during operation