Emission Control
Flue Gas Pre-treatment
GEA’s flue gas pretreatment provides advanced flue gas purification beyond emission control standards.
Therefore, cooling as well as condensing and removal of impurities like SO2 and SO3, aerosols and particulate matter < 1 µm are performed – enabling different carbon capture technologies.
GEA’s Gas Pretreatment
GEA’s gas pretreatment extends our regular emission control portfolio for advanced gas purification and is designed for easy integration at the end of our customers’ existing emission control system. Usually, it consists of two coupled units: the DCC and WESP.
GEA’s Direct Contact Cooler (DCC) does double duty: cooling and conditioning of the flue gas while also removing acidic components by pH-controlled injection of aqueous NaOH solution. GEA’s Wet Electrostatic Precipitator (WESP) is placed on top the DCC to remove particulate matter, mist and aerosols like SO3 in a compact design.
This combination enables cost-effective and adjustable flue gas pretreatment, preparing our customers individual flue gases to meet the requirements of their respective carbon capture units. To ensure a long service life of the system, GEA uses reliable technology with a self-cleaning system based on more than 30 years of experience.
Working principle of GEA’s Gas Pretreatment
For gas pretreatment, GEA’s products utilize evaporative and direct liquid-to-gas cooling in packed columns.
The technical implementation of a gas pretreatment systems is tailored to the presence of specific pollutant traces that need to be removed, and to the entire gas flow to be treated.
The aim of the gas pretreatment is to efficiently fulfill the necessary gas purification tasks in a single step.
Depending on specific needs, devices like the direct contact cooler (DCC), or wet electrostatic precipitator (wetESP) can be used.
Direct Contact Cooler (DCC)
In the Direct Contact Cooler (DCC) heat is directly transferred from the hot flue gas to the coolant. The DCC is filled with structured or unstructured packings made of materials that match the properties of the flue gases to enhance mass and heat transfer while maintaining a low pressure drop. Aqueous solutions are used as coolant, that enters in an evenly distributed manner from above and trickles down the packing in counter-current flow to the flue gas rising from below.
The formation of a thin film on the packing creates a large, volume specific heat and mass transfer surface. Due to the drop in temperature, water and other flue gas components condense and become entrained in the coolant. A demister is located at the upper end of the DCC to separate carry-over droplets from the conditioned flue gas.
After leaving the DCC at the sump, the heated coolant is cooled down via plate type heat exchanger. A second liquid is running in a closed loop to an air cooled heat dispenser, avoiding contamination of the packing and ensuring a long service life. Before reentering the DCC, reactive substances are added to the aqueous coolant, turning it into a scrubbing liquid to absorb chemical pollutants. For example, NaOH is injected to reduce SO2 content down to the target value and to perform a slight reduction of SO3.
Working principle of Direct Contact Cooler (DCC)
Wet electrostatic precipitator (wetESP)
The Wet Electrostatic Precipitator (WESP) efficiently removes residual fine dust particles < 1 µm as well as SOx mist or aerosols from vapor-saturated gases. GEA’s WESP consists of a compact arrangement of hundreds of discharge electrodes, which are surrounded by equidistant discharge electrodes. Between these, a high voltage electrical field charges the particles in the flue gas. These charged particles migrate to the electrodes, where they deposit and agglomerate.
Blow-down water is used to periodically flush the WESP to remove particles and condensates from the electrodes. In case the WESP functions as a second step after the DCC, both share the same casing with the WESP being placed on top of the DCC. In this step, a considerable reduction in the SO3 concentration is achieved, so that the expected value decrease below the standardized detection limit.
Working principle of Wet electrostatic precipitator (wetESP)
Downloads
Approfondimenti GEA
La biotecnologia a confronto con la realtà
Il nuovo Application and Technology Center (ATC) di GEA a Sarstedt, a sud di Hannover, non è né uno showroom né un laboratorio. È un luogo dedicato a test, raccolta dati e decisioni preliminari. È qui che si capisce se un concetto biologico può diventare un processo industriale solido. Si tratta di un passo più importante di quanto possa sembrare.
Cambiamenti nel settore del confezionamento alimentare: 4 tendenze
La termoformatura riveste da tempo un ruolo centrale nel settore del confezionamento alimentare. Ora si trova di fronte a un cambiamento radicale. Con l'inasprirsi delle normative, l'evoluzione dei materiali e l'aumento dei costi, le linee di formatura, riempimento e sigillatura non devono solo funzionare in modo affidabile: oggi hanno un ruolo fondamentale nel garantire che gli alimenti rimangano freschi, convenienti e riciclabili. Ecco le principali tendenze nella termoformatura che stanno plasmando il confezionamento e la consegna di prodotti alimentari.
