Pilot Tesis Test Üniteleri Membran Filtreleme Pilot Tesisi P

Kombine Spiral Sarımlı ve Plaka & Çerçeve Membran Filtreleme Pilot Tesis

Pilot ünite, dikkatlice seçilmiş saha cihazları ve kontrol vanaları ile birlikte operatör panelinde PLC ile anahtar proses parametrelerinin hassas bir şekilde gösterildiği uzun vadeli testlere olanak sağlamaktadır. Bu da manuel olarak kontrol edilen pilot tesislerle kıyaslandığında, ölçek büyütmede büyük avantajlar sağlamaktadır.

Membran tasarımı

Proses gereksinimlerinize en uygun çözümü bulmak için mevcut spiral sarımlı membran konfigürasyonlarını keşfedin:

  • Mikrofiltrasyon
  • Ultrafiltration

The area of the spiral wound membrane ranges from approx. 3‐7 m2 depending on membrane brand, type and thickness of the feed spacer.

The P&F loop is configured with 2.25 m2 membrane area in one section.

System design

  • Aimed at ultrafiltration of viscous (fermented) products
  • Two loops; loop 1 with two parallel 3.8” spiral wound membranes. Loop 2 is a P&F module with positive displacement pump. The loops can be operated in series or individually
  • Suitable for e.g. quark, cream cheese, protein standardization
  • Includes mixer for uniform feed inlet and retentate cooler for improved product quality
  • The product solids are regulated by ratio control
  • Feed inlet flow ranges: 100 – 400 lph

The control panel provides automatic continuous control of various process parameters and allows selection between different control modes:

  • Feed flow
  • Feed pressure
  • Temperature
  • Concentrate ratio control

Standard features

Skid mounted test unit. Wetted stainless steel in AISI 316L

Feed / CIP system

  • Feed/CIP pump, motor controlled by frequency converter
  • Pressure relief valve in P&F loop
  • Double safety filter
  • Tube and shell heat exchanger for heating
  • Temperature transmitter
  • Pressure indicators
  • Pressure transmitter
  • Feed flow transmitter
  • Retentate flow transmitter
  • Retentate control valve
  • Sample point

Loop system, up to two loops. The loops include:

  • Loop 1: One or two housings each one 3.8” spiral wound membrane.
  • Loop 2: P&F module with 2.25 m2 membrane area.
  • Positive pump
  • Recirculation pump, circulation pressure controlled by manually operated valve
  • Shaft seal water on recirculation pump
  • Tube and shell heat exchanger for cooling
  • Cooling water control valve
  • Permeate flow indicator
  • Temperature controller
  • Temperature indicator
  • Pressure indicators
  • Sample point
  • Possibility for loop isolation

Operating conditions

  • Membrane area up to approx. 16 m2 depending on type and number of membranes
  • Pressure up to 10 bar
  • Temperature up to 60°C

Utility requirements

  • Foot print approx. 315 x 215 cm, 1,800 kg
  • Power 400 V, 3‐phase, 50 Hz, PE, 24.78 kW
  • Cooling water 1° C, up to 3 m3/h depending on process and CIP temperature
  • Steam, low pressure, up to 100 kg/h (or hot water)
  • CIP water up to 15 m3/h depending on type and number of membranes
  • Please note our specific water requirements, available on request
  • Drain capacity up to 15 m3/h
  • CIP volume approx. 250 liters
  • Shaft seal water up to 0.2 m3/h
  • Compressed air 6 bar, water and oil free
  • Connections clamp Ø38